I have 2 hub cap wrenches for cars with larger hubcaps. These are larger than the 1930/31 hubcaps. (Maybe for Mike's Locomobile?)
The light colored wrench measures 3 and 1/2 inches across the open end. The other two wrench openings are 1 and 1/2 and 1 and 1/4 inch...
I wonder if anyone has one of the small handles for the seat adjuster on 1930 = 1932 Durants?
Will has just purchased a 1930 Durant Roadster and we need a handle for the seat adjuster.
Gord
Hi I am looking for distributor drive gears my housing is ok but the gears do not look like they belong. the distributor gear has been ground to fit and the generator gear is not centered in the housing.Generator number MC 4004 engine date 11/1922. I am thinking long...
This door handle has a shorter shaft than the sedan door handles, and has a stamped steel, flat baseplate unlike the curved cast baseplate on the sedan handles. It has the "spear point" design introduced in 1930.
I will bring this with me to the Durant meet in Gra...
Durant, Weston and Mott had extensive business dealings. This wrench is stamped "WESTON-MOTT CO". The large end will fit early Durant hubcaps. The other two wrench openings may fit anything. It also has two short pins on one side, but I do not know their purpose.
I...
One aluminum step plate which I believe is for a Star. It has a large Star in the middle of the step plate. There is one small crack in the left lower corner about an inch long. A good vintage driver quality step plate.
I will bring this with me to the meet in Grand...
A new set of 16 rubber universal joint balls. I previously bought these thinking they were needed for my 1930 Durant. They are for earlier model cars, not 1930.I will bring these with me to the Durant Meet in Grand Junction next week.
1923 Durant Star touring automobile
Needs complete restoration and has serious rust issues with that said everything is here motor with all parts are in decent shape frame is complete. Car was parked by family after a loss in family and sat under a tree and melted....
1923 Durant Star touring automobile
Needs complete restoration and has serious rust issues with that said everything is here motor with all parts are in decent shape frame is complete. Car was parked by family after a loss in family and sat under a tree and melted....
Several years ago, back in the Jeff Gillis days, John Baraldi was manufacturing new Rocker Arms for the A22 Durant motors. Does anyone have a set that they would like to part with, or have any information on them. We have broken one of the original ones on our 1922 E...
I have a garage full of parts - What do you need?
7 hoods,5 transmissions, 3 sets of springs, 4 ring gears, 2 1/2 motors, 2 rear ends, front assembly, 4 radiators w/cowl, many brake drums and parts, manifolds, pumps, crankshafts, heads, shocks, spokes, electrical pa...
I'm looking for parts to a 15U motor (1928-1930)
needing a:
Generator (chain driven) Auto-Lite # GAL 4104
Distributor Auto-Lite # IGB 4008B
520 818 3391 flintauto@gmail.com
1963 AACA National First Prize winner 1925 Star Touring car. A very solid and good running car that still presents well. Has steel disc wheels, all gauges & lights work except speedo. Steel body and fenders, good tires and tubes. Comes with a very nice comfy brown le...
In case anyone missed this--Lance Hayes in San Diego wants to get rid of his Durant parts for free or cheap. His health is declining and he wants to help out where he can. His notice is posted in the "test only" section on the forum menu and it may not have been noti...
Years ago, may have been in the Jeff Gillis days, someone reproduced the Star sign which said, " Low cost Transportation, Star Cars, Authorized Service, Durant Motors". Does anyone know where I can get one of these signs, or if anyone is still making them Regards, Curt
My car has the Chevy style oval tail light. I have several plugs with the protruding spring loaded pins but they all protrude too far to engage the pins that lock the plug into the socket. I need the plug and I'm missing the license plate light lens. Any one know whe...
Saw this 23 Dort on Craigslist. It is located in Bakersfield CA. I saw the car at a pawn shop in Bakersfield about 5 years ago. The description says engine runs well but the upper radiator hose is missing (exactly the same as it was 5 years ago). If anyone is interes...
Looking for a 19 inch, 6 lug wire wheel, 6 1/2 inch center for a 1930 6-17 Durant, should be the same as for 6-14
Bob Smith 520 818 3391 flintauto@gmail.com
I am looking for a motometer for my 1928 Durant M-2. I have seen them advertised on Restoration Supply but I was interested if someone reading this post might have one to sell.
There is a sedan on BringATrailer with a Hayes built body like some of our cars. A 1929 Marmon model 78 with a straight 8. Some similarities in styling with our cars (although a lot of cars from the era where close in looks). Photo #107 shows a Hayes body tag from th...
FOLLOWING FOR SALE:
FRONT SHEET METAL INCLUDING FRONT FENDERS,HOOD , RAD SHELL, LOWER PAN
1930 DURANT FRAME, GOOD SHAPE
1929 DURANT BRAKE BACKING PLATES WITH ALL LITTLE PARTS FOR WIRE WHEELS
( ALL 4 WHEELS SET)...WIRE WHEELS GONE.
SOME OTHER SMALL PARTS...FOR 3...
Shop owner was cleaning out the shop and found an abandoned project that he'd like to sell. Shown is a '28 Durant Continental W5, fresh valve job, new pistons, crank and cam have been either cleaned up spotless or they're new as well, I don't know much about it other...
There is a 1931 DeVaux for sale at the Pioneer Auto Show, in Murdo, SD. I have had the car on the Registry for years.
I called to get some information. It is a complete (but well worn) car. The ID is correct and they have a clear title.
Check it out. They are o...
My 26' M 4dr sedan was pretty much missing much of the interior when I got it and over the years I have rounded up a lot of what was missing. I am now getting near reupholstering the interior and uncertain about whether there was a garnish molding around the rear win...
Homemade Tractor with a Geneva Adapto Tractor Kit. Built and modifications done in the late 1930's. COWL Model NE 8027, 1923 motor W4 #4130XX. Restored in 1975 and always stored inside. Slow speed and neat old tractor. For sale for $2,800.
Star 4 cylinder motor with flywheel, clutch, radiator and radiator housing for sale. Serial number is 53267, reportedly from a 1927 Star but have also been told it is from a few years earlier. Appears to be all there with distributor, coil, starter, etc.. Radiator ha...
I'm looking for a Spicer ball type u-joint coupling for my 1929 Rugby 401 as used on many Rugby/Durant vehicle models around that time. This is a link to photos of the coupling part that I seek https://drive.google.com/drive/folders/1tBifWbpKY6gE7rgCkRR2JthDGyQbMNKH?...
Hi, a friend of mine has a large Durant Motors metal sign that he is wanting to sell. It is 48" x 96" he is asking $1500 for the sign. I can text a picture to anyone interested. My number is 308 293 5764
I have an original set of early Durant club magazines for sale.
They are from the first 22 years of the club.
They go from May 1976 (Volume #1 issue #1 to Volume #5 issue #4 - February 1981) when the title was the "Durant Family Registry".
The title changed with...
Hello:
I'm looking for a right side emergency brake band and spring for my car above.
Any condition can be used as I can always re-lign the band.
Thanks for helping.
Mike
https://ibb.co/XWpGFxT
https://ibb.co/XFJgZ4F
https://ibb.co/ydyPmFX
https://ibb.co/TB...
Somewhere along the way on my long restoration of my 1929 Rugby 401 truck I seem to have lost some parts of the clutch linkage connecting the pedal (which I have) through to and including the clutch throw out bearing. From what I understand these components are the s...
I have been searching for rubber molding for my '32 DeVaux swing-out windshield...Not sure if any other of our later Durants use the same molding or not....It is not the same as our '28 or '29s...I have went through approx 312 pages of WEFCO Rubber on-line extrusion...
My 1927 touring is for sale. It's 93 % complete and partially restored. It is not running at this time but the engine compartment is all there but in general the motor needs rebuilding.Have a clear title. Asking $3,000.00, if your seriously interested give me a call,...
I have for sale a W4 (130 cu in) and 14L (169 cu in) engines. The W4 is basically complete. The 14L is just a long block. Both have been stored in Mike Larsens garage and both turn over easily.Price is $25 or OBO. Consider parting out if you just need a few internal...
As a lot of you know about a year and a half ago I bought the 1931 devaux custom coupe that was being restored by bob fossgreen before he passed away,fast forward Gary Yelle and I was talking about restorations and Gary said how long are we going to live,in the mean...
I am hoping that Norm and/or Bob Smith see this post. About 2 weeks ago I got a E-mail from a young man (well, everyone is younger than me) that was wanting advise on buying a DeVaux that had a lot of work already done. My advise was to buy it. So he did this last we...
In case you missed it--Cliff Durant's Locomobile for sale(Billy's son). Hyman Ltd has cliff Durant's Locomobile on their website-$89,500.00. Does go into an interesting history in the description.
I have an original 1929 Durant M2 Radiator for sale. It appears to be in very good condition. I'm asking $300 and can provide pictures on request. Feel free to call or text 570-994-4674.
Thanks
I am restoring a my 1928 Durant M2 and I am in need of many parts. My list is Distributor
Headlights
Tires
Coil
Radiator hose
Pulley
Belt
Fan
Starter
Hand crank
Head studs
Bendex spring
inside handles
rear view mirror
Carburetor
Water neck for the top...