AGRR™ magazine/glassBYTEs.com™ Message Forum

AGRR Magazine
AGRR™ Magazine

glassBYTEs.com

AGRSS

NWRA

Key Media & Research
Privacy Policy


ATTENTIONThe glassBYTEs.com forum is being retooled and will return with a new look and functionality that will hopefully help our readers even more. Watch for an announcement when it will be ready, it will be a few months.

You can still stay up on daily news and comment on stories by signing up for the glassBYTEs daily e-newsletter at glass.com/subcenter. There is no charge. Hope to see you there!
General Forum
This Forum is Locked
Author
Comment
View Entire Thread
Re: toyota prius door switch not working?

I don't know if this will help or not, but here is the resets for the Toyota Prius. It may help.

• When a power window regulator motor assembly is replaced, DTC B2313 is stored. Clear the DTC after initialization.
• When performing initialization, do not perform any other procedures.
• When performing initialization, use the power window switch of each door to initialize each door window.
• If initialization is not completed properly, the LIN communication system may have a malfunction .
• Make sure to park the vehicle and turn off all the electrical systems before performing initialization. Initialization will be canceled if the vehicle is driven during initialization.
• Make sure not to hit, strike or vibrate the door window glass during initialization because the vehicle is learning the sliding resistance of the door window glass.
• Make sure not to turn the engine switch to on (IG) or off during initialization.
HINT:
When the battery is replaced, it is not necessary to initialize the power window regulator motor assembly.
CONDITION OF POWER WINDOW PROCEED TO
Initialization method when a power window regulator motor assembly has been replaced with a new one. Procedure A
Initialization method when a power window regulator motor assembly has been removed/installed or a door glass and/or door glass run etc. have been removed/installed or replaced with new ones.
HINT:
Use this procedure if the power window regulator motor assembly has been reused. Procedure B
Initialization method when a reverse rotation malfunction occurs due to a sliding resistance change resulting from adjustment etc. Procedure C

(b) Procedure A
(1) Connect the battery and turn the engine switch to on (IG) (at this time, the LED on the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assembly blinks to indicate that it is ready for initialization).
(2) Fully open the window by fully pushing down the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assembly, and hold the switch for 1 second or more after the window is fully opened.
(3) Fully close the power window by fully pulling up the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assembly, and hold the switch for 1 second or more after the window is fully closed to reset the glass position. The LED on the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assembly stops blinking and illuminates to indicate that initialization is complete.
(c) Procedure B
(1) Connect the battery and turn the engine switch to on (IG).
(2) Fully close the power window by fully pulling up the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assembly, and hold the switch for 6 seconds or more after the window is fully closed (if the power window does not move or stops halfway even when the switch is fully pulled up, release the switch and fully pull it again).
(3) Fully open the window by pushing down the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assembly, and hold the switch for 1 second or more after the window is fully opened.
(4) Release the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assembly. Then fully push down and hold the switch for 4 seconds or more.
(5) Fully close the power window by fully pulling up the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assembly, and hold the switch for 1 second or more after the window is fully closed to reset the glass position and complete initialization.
d) Procedure C
(1) Connect the battery and turn the engine switch to on (IG).
(2) Fully open the window by fully pushing down the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assembly, and hold the switch for 1 second or more after the window is fully opened.
(3) Fully close the power window by fully pulling up the multiplex network master switch assembly, power window regulator switch assembly or rear power window regulator switch assembly, and hold the switch for 1 second or more after the window is fully closed to reset the glass position and complete initialization.

Re: toyota prius door switch not working?

thank you, we will give it a try

Copyright © AGRR™/glassBYTEs™ All rights reserved.
20 PGA Drive, Suite 201, Stafford, Virginia 22554
540-720-5584 (P) 540-720-5687 (F) info@agrrmag.com
www.agrrmag.com / www.glassbytes.com