​​​​​​​

Durant Motors Internet Forum

Our Purpose

  Preserve the automobiles manufactured by the Durant Motor Company, provide enjoyment for each member with meets, tours & technical assistance.


This forum is provided by the Durant Motors Automobile Club located at durantmotors.org





How to Add Pictures 

General Discussion Forum
Start a New Topic 
78 79 80 81 82 83 84 85 86 87
Topic
Author
Views
Replies
Last Post
Cluch maintenance issue
Does anyone know how the Clutch release bearing connects to the Hardy joint in a 1927. Durant Rugby?
Views: 343   Replies: 3
Last Post: Feb 16, 2006 12:15am
by orosz csaba
Looking for Rugby parts
Hi, I am looking for parts for my 1927. Durant Rugby: - Continental 14 engine (complete) - Brush set for the starter - Brush set for the dynamo - Front turn signal lights - Klakson horn - Rear combination light - Ignition switch - Ignition cabel - Turn sig...
Views: 292   Replies: 2
Last Post: Feb 15, 2006 11:50pm
by orosz csaba
283 chev engine
I have a 1964 chev impala 283 engine for sale --it is profesionally rebuilt with new pistons and rings--bearings--oilpump- camshaft and bearings -has been bored 30 thou over --crank turned 10 and 10 heads are all rebuilt -valves all done - It is complete from i...
Views: 169   Replies: 0
Last Post: Feb 15, 2006 10:19pm
by Ken McCormick`
December club magazine
Hello everyone. Poor Bob Krause (84 years old) just North of me up in Long Beach Ca. just called and said he finally got all the mailing labels attached and all the right postage on all the magazines and Mike Larsen’s dues renewal envelope inside with 3 seal ta...
Views: 273   Replies: 1
Last Post: Feb 13, 2006 3:09pm
by Lance Haynes
Thanks to Rick Botti
Sir Rick: Thanks for your telephone call Sunday Evening. Imagine, being consumed with Startalk all through "60 Minutes" and then some. And thanks for posting the photos of the "new" 26 Star R Coach. You are a wealth of information, and it adds to the intrigue of thi...
Views: 169   Replies: 0
Last Post: Feb 13, 2006 2:28am
by Ron Hast
vacuum fuel pump
stewart warner 403 d u8, need float,are whole ass. 1927 star touring
Views: 219   Replies: 0
Last Post: Feb 9, 2006 6:08pm
by gary blalock
Gas line pressure regulator
Anybody using a gas pressure regulator on their cars? If so, where can I get one? Also, what is proper fuel pressure from fuel pump to Stromberg U-2 carb.? I have been told 2psi, but can't confirm that. Jim
Views: 366   Replies: 9
Last Post: Feb 9, 2006 3:37pm
by Jan Arnett
Turlock Calif. Swap Meet Report
Before 6:00 a.m. in pitch dark, and rain, thousands of people had arrived and were standing in line to enter this awesome event. The entire fair grounds were covered in what most would describe as "junk". Most prominent other than people were the hundreds if not thou...
Views: 288   Replies: 4
Last Post: Feb 7, 2006 4:25pm
by Ken McCormick`
Home stretch--Hemmings
Hello, Thanks for all the help you have given (you know who you are). I am still in desperate need of the exterior dimensions of the 614: Overall length Overall width Overall height Front track Rear track I do have a full set of specs for the '3...
Views: 343   Replies: 3
Last Post: Feb 7, 2006 12:45pm
by D. Traver Adolph...
Valves for 22A
I am in the start of rebuilding a spare Contintal 22A engine for my '30 Durant. It will be retrofitted with insert berings for both the mains and con rods. I also plan to install a 12 v system with electonic ignition. But... I need a set of valves, valve springs an...
Views: 204   Replies: 1
Last Post: Feb 6, 2006 7:02pm
by gary kauffman
Unwanted E mail
Have any of the other members been getting e mail asking if you want to sell your car or any parts of cars?? I have a hunch these are maybe hackers trying to get into my puter to plant virus or some other nasty thing . I have had three requests to buy my car --and a...
Views: 294   Replies: 4
Last Post: Feb 6, 2006 1:13pm
by Norm Toone
Parts Needed for Star M Coupe
I am trying to build 2 Star M coupes. One, a 26 model and the other a 27 model. It seems like most parts are the same except the door latch mechanisms. However, there are not enough small parts to complete one car much less both of them. Parts needed at present:...
Views: 244   Replies: 2
Last Post: Feb 3, 2006 5:07pm
by Don Shilling
1927 star
have 27 star touring, need fuel pump stewert warner fuel pump, or float, 403 d u8 hard to read numbers THANKS really nice car , my dad spent alot of time to make it worthy of a calander pic.
Views: 202   Replies: 0
Last Post: Feb 2, 2006 3:38pm
by gary blalock
Restoration Info Rquired
All to many times I see for sale adds that say amature restoration. I think we all have a certian amount of pride doing things for ourselves or we wouldn't be into the old car hobby. In the 1920's I would think that a lot of cars were made useing similar technics and...
Views: 554   Replies: 12
Last Post: Feb 1, 2006 1:49pm
by Ken McCormick
Durant promotional pocket watch.....OLD!!
I was just doing a web search on Durant as I have an Elgin pocket watch from the 20's. That I am in the process of restoring. The watch appears to be a promotional item commissioned by Durant and was probably given to a dealership owner or Durant executive. The...
Views: 208   Replies: 0
Last Post: Feb 1, 2006 10:37am
by dave bolls
Clutch spring ?
I am working on my 1929 Durant Touring. I just got the engine completely rebuilt. Now I'm putting the car back together. Will someone Please tell me? Is there suppose to be a spring on the clutch petal? What holds the petal from going in too far or out too far?...
Views: 273   Replies: 2
Last Post: Jan 31, 2006 3:06pm
by Leonard Burkhold...
The History Channel
I just posted a short article on The History Channel the title of which is "The Transportation Industries Forgotten Man". It is under the topic "Save Our History". Back in either 1999 or 2000 I tried to get our DMAC members to send live shots of their automobiles fo...
Views: 238   Replies: 3
Last Post: Jan 29, 2006 8:55pm
by Mike Rice
Star Coupe Measurments
Hi Guys! Things are progressing nicely on the two M coupes. Butch is doing all the sandblasting and I'm doing the wood work. I've got the door hinge and latch posts made and the corresponding metal fitting nicely. Now, I'm ready to construct a jig to assemble the win...
Views: 170   Replies: 0
Last Post: Jan 29, 2006 6:15pm
by Don Shilling
Star Coupe Wood
Does anyone have any pics of a de-skined Star M Coupe. The only info I have to study at present are pics of a '29 D-60 coupe and a '26 Coupester. I'm trying to recreate the wood framework and have precious little original wood to make patterns from. If you send by...
Views: 230   Replies: 3
Last Post: Jan 29, 2006 1:06pm
by Bill DeVries
TWO 4cyl Continental motors for Durants
I hope you all had a very Merry Christmas and will have an even Happier New Years. I'm acting as a 3rd. party in trying to sell 2 Continental 4cyl motors for a friend in Flint Michigan. The 1st. one was removed from a 1927 Durant and is complete with attachments...
Views: 289   Replies: 1
Last Post: Jan 28, 2006 7:50pm
by zac piper
Radiator or License plate topper for DMAC
OK Durantonians we have posted the pictures of the designs we have received so far on the web site. They will also be posted if possible in the next Durant Partner. Not this one but the next. Soooo let's start voting on them. You can send the votes to me if you'd lik...
Views: 191   Replies: 2
Last Post: Jan 28, 2006 6:34am
by Mike Linthicum
2006 Dues
Can we still pay our club dues via Paypal? If so, where is the limk? Thanks, Don
Views: 553   Replies: 18
Last Post: Jan 27, 2006 6:18pm
by Jan Arnett
List of Durant & Star Dealerships
Hi All I'm in the process of compiling a list of Durant & Star dealerships. I need your help ! ! Look on any literature and advertising materials you have in your collection. Any info that you can forward to me will be appreciated. What dates did the d...
Views: 727   Replies: 19
Last Post: Jan 27, 2006 2:32pm
by anon coward
DMAC is now incorporated as a non-profit corporation!
Fellow Durantonians On January 18, 2006 we were officially incorporated as a non-profit corporation. In December with the approval of the Board of Directors I initiated the process for incorporation. Since the DMAC is a multi-state and worldwide organization w...
Views: 178   Replies: 3
Last Post: Jan 27, 2006 10:48am
by Lance Haynes
Thanks - and seeking wisdom....
Thanks Yates and Gordon for info leading to "dog bone and motometers." My 26 Star 6 cyl. has a 1 3/4" pipe externally threaded. All others available seem to be 2 inches. Also -- seeking wisdom: Have minor chip in "Star" emblem on front of chrome radiator housing....
Views: 568   Replies: 5
Last Post: Jan 26, 2006 2:40pm
by Ronald Hast
Star Car Engine for Sale
I have discovered a Star Car 4-cyl Continental complete engine, s/n 41145 with frame and rear end in the backwoods. Please contact if interested.
Views: 299   Replies: 1
Last Post: Jan 26, 2006 7:07am
by Clay Pass
carburetor
Need a carburetor for a 1925 Star Touring Car equipped with a 4 cylinder Continental Engine. Existing Carb. made of white metal which is powdering or disintegrating. Need a modern manufactured after market unit for the Star.
Views: 276   Replies: 3
Last Post: Jan 26, 2006 6:51am
by Clay Pass
Model A sponsored swapmeet in Turlock, CA 1-28/29
Planning to attend the Turlock CA. event reportedly quite huge, sponsored by Model A clubs. Have former attendees found many Star items in the mix? Don't need much of anything, but would be fun to find such items as Star 6 radiator housing emblem (blue/red/white - 2"...
Views: 203   Replies: 7
Last Post: Jan 25, 2006 5:45pm
by Charles A. Spitz
Durant Partner?
Have the Durant Partner's gone out yet? I've been looking for it and thought maybe it's been lost.
Views: 168   Replies: 1
Last Post: Jan 25, 2006 5:30pm
by Rick Botti
What information do you want to see in the magazine
Ok. I would like for everyone to chime in and tell me what subject of articles you would like to see in the magazine. There was a time when a lot of people asked for specific information but that time seems to have passed. Two subjects I am working on are one, how...
Views: 357   Replies: 9
Last Post: Jan 25, 2006 10:29am
by Ricardo H.Colomb...
Durant Motors detailed cloisonné lapel or hat pin ¾ “in size in full color.
Custom designed highly detailed brand new cloisonné Durant Motors lapel or hat pin. Brand new manufactured limited edition ¾” Cloisonné lapel or hat pin in full color. Copy of the Durant Motors first radiator emblem. Send $6.99 plus $.50 Postage...
Views: 461   Replies: 10
Last Post: Jan 25, 2006 7:37am
by Rick Botti
1915 Star canvas top assembly
Looking for pics or help in assembly of the canvas roof for the restoration of a 1915 Star. Now running, done with interior, have roof frame but stuck on fabric and correct assembly. Have no model of correct assembly or pictures.
Views: 202   Replies: 5
Last Post: Jan 24, 2006 2:26pm
by John Kulas
Star & Durant Reamers on Ebay
Ok Durantonians I have a question for you. There is a set of Star or Durant Reamers for sale now on Ebay. I think Bob has bid on them. What the heck are the for? what would you Ream?
Views: 151   Replies: 1
Last Post: Jan 24, 2006 12:40pm
by Frank Witkowski
Looking for Dog Bone (?) radiator cap for 26 Star R
New member...trying to find source for new radiator cap. Car frame off restoration, last item is radiator cap to fit externally threaded pipe affixed to internal radiator. Thanks!!
Views: 224   Replies: 2
Last Post: Jan 23, 2006 12:45pm
by Yates Milton
Sad News
Bob Krause sent me a Christmas card and a letter recaping his activities for 2005. It is with sadness I report that Bob lost his son John at age 57 from a massive heart attack. Bob also lost his second wife Martha of 17 years on December 18th. Must admit this bad ne...
Views: 378   Replies: 5
Last Post: Jan 23, 2006 12:10am
by Lance Haynes
Star Coupe and A-22 Sedan Project
I have two Star M coupe projects in progress. One belonging to Butch James is a ’26 and mine is a ’27. Both have been previously attempted to restore. We have enough parts to partially complete both but not enough parts to build one car. In addition, the...
Views: 162   Replies: 0
Last Post: Jan 21, 2006 11:40am
by Don Shilling
Seeking 26 Star Radiator Badge (6 cylinder)
Looking for (new or ?) blue radiator badge for 26 Star 6 cylinder
Views: 147   Replies: 0
Last Post: Jan 21, 2006 11:00am
by Ronald Hast
Stop Light/Turn Signals for Safety sake.
Since people today do not realize that these Old Cars do not stop as quick as the more Modern ones. We need to give them advance notice of what we are going to do. Because of this I installed a dual element bulb in my Tail Light. To get it to work I used a rocker ar...
Views: 298   Replies: 5
Last Post: Jan 20, 2006 5:24pm
by Jan Arnett
14L Overhaul specs
My 14L engine in the 1929 Model 60 has develope some BAD oil leaks and I'm thinking of pulling it to reseat the bearings and reseal the the parts. It also has a drop in Oil pressure to about 7lbs when it warms up. Anyone know were I might find srevice or build specs...
Views: 145   Replies: 0
Last Post: Jan 18, 2006 9:40pm
by Joe Osbone
New Pictures
Added new pictures of Louis Quenneville's 1923 Depot Hack Restoration project to the Star Page. Rick
Views: 191   Replies: 0
Last Post: Jan 17, 2006 11:23pm
by Rick Botti
water pump parts
Hello everyone, just finished a batch of replacment parts for water pumps. I have availible the pump packing nut and it fits the models M M2 M4 40 R 55 60. Also availible the water pump cover which is usually very thin and corroded. I have these in stainless steel...
Views: 175   Replies: 0
Last Post: Jan 17, 2006 9:37pm
by Franz Fraitzl
There may possibly be some downtime
Our Forum service provider will be performing major system upgrades this weekend in an effort to keep up with demand and growth. While they do not anticipate lengthy periods of downtime users may experience intermittent periods where their services are not online....
Views: 147   Replies: 0
Last Post: Jan 17, 2006 8:24pm
by Rick Botti
Gauge Source
Greg Gleason at gpg@cableone.net specializes in antique automotive gauges. When contacting him please try to send a photo of the front and back of the gauge you need. Dave
Views: 221   Replies: 0
Last Post: Jan 17, 2006 10:13am
by Dave Schulte
Automotive Books
I just received an advertisement from McFarland and Company, Publishers, on their Automotive Books for 2005-2006. One caught my eye. "Chrysler, Ford, Durant and Sloan, Founding Giants of the American Automotive Industry". On checking the web site I found a lot of g...
Views: 196   Replies: 0
Last Post: Jan 16, 2006 8:54pm
by Gary Yelle
tail lights/turn signals
I've been wanting to ask this for some time and keep forgetting. Jan's Dodge tail light and magazine article question reminded me. My 31 model 619 as most Durants has one tail light. Getting out on the road more, I am consious that many people today do not know why m...
Views: 264   Replies: 5
Last Post: Jan 14, 2006 6:49pm
by Jan Arnett
31 614 vs 31 DeVaux
David's question got me thinking. We all know that a lot of Durant technology was used to make the DeVaux. I know the 22A engine has the same gaskets as the DeVaux 40A engine except for the manafold. The brakes are also the same. The wheelbase for the DeVaux is...
Views: 207   Replies: 0
Last Post: Jan 13, 2006 10:51pm
by Gary Yelle
1930 Durant Roadster
Hi, I'm sure many of you have seen the very nice 30 roadster on Ebay. How many of them are there out there? Here are the ones I know about. Al Scholes on the East Coast. Reg Bent in Canada. Will Dyck in California. Jim Colbert in Utah? Mine in Iowa The one on...
Views: 261   Replies: 1
Last Post: Jan 13, 2006 10:48am
by Lance Haynes
Texaco Products
My son, Mike, has purchased many Texaco Products from an estate. Items such as oil filters, points and condensers, HD flashers, oil filler caps, thermostats and other items. For example Texaco # cc30 Contact & Condenser Texaco # cc60 Contact & Condense...
Views: 240   Replies: 1
Last Post: Jan 13, 2006 7:53am
by Jack Malpass
Durant article in Hemmings
Hello. For only the second time in the last 35 years, Hemmings will be running a full driveReport on a Durant, in this case a 1931 614 De Luxe sedan. I would like to enlist the help of this group, if possible, in ensuring my data are accurate. To that end, I'm pos...
Views: 805   Replies: 3
Last Post: Jan 12, 2006 3:47pm
by Lance Haynes
1928/29 Durant Coupe
Becky Leach has her grandfather's 1928 or 1929 Durant Coupe 4 cyl. She is thinking of having it crush if she can not find a new home for it. It is rough but could be a good project or parts car. She is in Ohio and can be reached at leachbm@sbcglobal.net I am sure a...
Views: 219   Replies: 0
Last Post: Jan 12, 2006 4:07am
by bob smith
78 79 80 81 82 83 84 85 86 87

 

The Durant Motors Automobile Club